Saturday, August 15, 2009

Rangkaian Pengusir Nyamuk

This is a circuit diagram of an ultrasonic mosquito repeller (pengusi yamuk). The circuit is based on the theory that insects like mosquito can be repelled by using sound frequencies in the ultrasonic (above 20KHz) range. The circuit is nothing but a PLL IC CMOS 4047 wired as an oscillator working at 22KHz. A complementary symmetry amplifier consisting of four transistor is used to amplify the sound. Speaker Piezo buzzer converts the output of amplifier to ultrasonic sound that can be heard by the insects.
Rangkaian Pengusir Nyamuk
Skema Rangkaian Pengusir Nyamuk

The circuit can be powered from 12V DC. The buzzer can be any general purpose piezo buzzer.

Description IC CD4047B

IC CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and an external resistor (between pins 2 and 3) to determine the output pulse width in the monostable mode, and the output frequency in the astable mode. Astable operation is enabled by a high level on the astable input or low level on the astable input. The output frequency (at 50% duty cycle) at Q and Q outputs is determined by the timing components. A frequency twice that of Q is available at the Oscillator Output; a 50% duty cycle is not guaranteed. Monostable operation is obtained when the device is triggered by low-to-high transition at a trigger input or high-tolow transition at b trigger input. The device can be retriggered by applying a simultaneous low-to-high transition to
both the a trigger and retrigger inputs. A high level on Reset input resets the outputs Q to low, Q to high.
Lay out IC CD4047B

Block and Connection Diagrams IC CD4047B

IC CD4047B Applications

Frequency discriminators
Timing circuits
Time-delay applications
Envelope detection
Frequency multiplication
Frequency division

READMORE...

Friday, August 14, 2009

Rangkaian Pendeteksi (Sensor) Kelembaban Udara

Pendeteksi (Sensor) Kelembaban Udara

Dew ad- versely affects the normal per- formance of sensitive electronic devices. A low-cost circuit described here can be used to switch off any gadget automatically in case of excessive humidity. At the heart of the circuit is an inexpensive (resistor type) dew sensor element. Although dew sensor elements are widely used in video cassette players and recorders, these may not be easily available in local market. However, the same can be procured from authorised service centres of reputed companies. The author used the dew sensor for FUNAI VCP model No. V.I.P. 3000A (Part No: 6808-08-04, reference no. 336) in his prototype. In practice, it is observed that all dew sensors available for video application possess the same electrical characteristics irrespective of their physical shape/size, and hence are interchangeable and can be used in this project.



Pendeteksi (Sensor) Kelembaban Udara
Skema Rangkaian Pendeteksi (Sensor) Kelembaban Udara



The circuit is basically a switching type circuit made with the help of a popular dual op-amp IC LM358N which is configured here as a comparator. (Note that only one half of the IC is used here.) Under normal conditions, resistance of the dew sensor is low (1 kilo-ohm or so) and thus the voltage at its non-inverting terminal (pin 3) is low compared to that at its inverting input (pin 2) terminal. The corresponding output of the comparator (at pin 1) is accordingly low and thus nothing happens in the circuit. When humidity exceeds 80 per cent, the sensor resistance increases rapidly. As a result, the non-inverting pin becomes more positive than the inverting pin. This pushes up the output of IC1 to a high level. As a consequence, the LED inside the opto-coupler is energised. At the same time LED1 provides a visual indication. The opto-coupler can be suitably interfaced to any electronic device for switching purpose. Circuit comprising diode D2, resistors R5 and R6 and capacitor C1 forms a low-voltage, low-current power supply unit. This simple arrangement obviates the requirement for a bulky and expensive step-down transformer.

READMORE...

Rangkaian Alarm pendeteksi Api menggunakan LDR

In the rooms are vulnerable to fire, such as a storage material flammable, required a system of prevention of the occurrence of fire. For example, using a fire alarm, so that eg arise if a flame, can be quickly and by others that can immediately fire it does not cause a fire is greater.

Here is a simple fire alarm circuit based on a LDR and lamp pair for sensing the fire.The alarm works by sensing the smoke produced during fire.The circuit produces an audible alarm when the fire breaks out with smoke.

Fire alarm circuit Skema rangkaian alarm pendeteksi api|kebakaran

Note:
  • The speaker can be a 8Ω tweeter.
  • POT R4 can be used to adjust the sensitivity of the alarm.
  • POT R3 can be used for varying the volume of the alarm.
  • Any general purpose NPN transistor( BC548,BC148,2N222) can be used for Q1.
  • The circuit can be powered from a 9V battery or a 9V DC power supply.
  • Instead of bulb you can use a bright LED with a 1K resistor series to it.

When there is no smoke the light from the bulb will be directly falling on the LDR.The LDR resistance will be low and so the voltage across it (below .6V).The transistor will be OFF and nothing happens.When there is sufficient smoke to mask the light from falling on LDR, the LDR resistance increases and so do the voltage across it.Now the transistor will switch to ON.This gives power to the IC1 and it outputs 5V.This powers the tone generator IC UM66 (IC2) to play a music.This music will be amplified by IC3 (TDA 2002) to drive the speaker.

The diode D1 and D2 in combination drops 1.4 V to give the rated voltage (3.5V ) to UM66 .UM 66 cannot withstand more than 4V.

READMORE...

Rangkaian Sekring|Fuse Otomatis

To restrict / security, electric current is usually used fuse/sekring or patron is dissolved when going short (konslet) will drop out and must be replaced with a new one. Then, in order not to drop out of each new change means that more money out to buy, then there fuse/sekring automatically work with the reset button. So there are problems with each short, fuse/sekring will automatic decided flow then to return it does not need to buy a new (if not broken) just press the reset the equipment will live again.

This is one of the simplest electronic fuse circuit one can make. The circuit uses only one transistor, one SCR, one push button switch and two resistors.

Simple electronic fuse
Skema Rangkaian Sekring|Fuse Otomatis


The value of R1 can be obtained from the equation; [Imax] X [R1] = 0.7V.
R2 can be obtained from the equation; R2 = [Vs] X [1K Ohms].
Wattage rating of R1 can be obtained from the equation; W = [Imax] X [Imax] X [R1].
For this circuit to work the current consumption of the load must be greater than the holding current of the SCR.

The working of the circuit is very simple. Initially the load current flows through SCR and resistor R1.The value of R1 is so selected that, the maximum load current multiplied by the resistance of R1 is equal to 0.7 volts. When the load current exceeds the maximum value the voltage drop across R1 becomes more than 0.7V and switches transistor Q1 ON. Now the transistor completely bye passes the load current and the current through triac falls below the holding current. This makes the triac OFF. When SCR is OFF there will not be any current flow through R1 and so the voltage across it falls to 0.This makes the transistor OFF, completely isolating the load circuit.The fuse can be resetted by pressing S1.When S1 is pressed the SCR is again triggered and remains latched to conduct the load current.


READMORE...

Rangkaian Regulator menggunakan Op-Amp

Regulator is a series of regulations or the voltage output from power so that a portion darinaik effects or voltage drop in net does not affect the voltage ration power to be so stable.


Regular circuit of regulators have been good if the ripple voltage is small, but there is a problem of stability. If the voltage PLN rise /down, then the output voltage is also will be rise /donw. regular circuit of regulators, if the current of the larger, the dc voltage output is also down. For some applications this voltage change will very disrupt.

Rangkaian Regulator menggunakan Op-Amp


Regulator using Op-AmpSkema rangkaian regulator menggunakan OP-Amp

Technical regulations that better is to use the Op-Amp for a drive-transistor Q. Dioda zener here do not give directly to the bait transistor Q, but as a reference voltage for the Op-Amp IC1. Feedback on the negative pin Op-amp is a snippet from the voltage regulator out, namely:
Regulator using Op-AmpIf the voltage V out exit Ascending, voltage V in (-) also Ascending until this voltage is the same as the reference voltage Vz. Likewise if the voltage V out decreases exit, for example because of supply current to the load increases, Op-amp will maintain stability in the V reference point z with the current IB to the transistor Q1 so that at any time in the Op-amp maintain stability:
Regulator using Op-Amp
Ignore the VBE voltage transistor Q1 and mensubsitusi formula, obtained by mathematical relationships
Regulator using Op-Amp
In the circuit of regulator Op-Amp of this output voltage can be adjusted with the set of R1 and R2.

READMORE...

Wednesday, August 12, 2009

Rangkaian Regulator menggunakan Diode Zener

Regulator is a circuit of regulations or the voltage output from a ration resources so that the effects of increased tension or decrease in net does not affect the voltage ration power to be so stable.


Rangkaian Dasar Regulator Diode Zener

Simple circuit regulator , working on the zener breakdown voltage so that it produces the same output with the zener voltage, however, this circuit is only useful if the current burden of not more than 50mA. simple circuit regulator using zener diode can you see in the circuit under the scheme

Circuit of regulator using diode Zener
Skema rangkaian Regulator Dioda Zener dasar

voltage output:
Rangkaian regulator Diode ZenerResistor value
Circuit of regulator using diode ZenerWith this design approach, you must check the power ratings of your output resistor and Zener diode to make sure they are able to handle the power requirements.

The power rating load of resistor and zener diode must be at least of they are able to handle
Rangkaian Regulator Zener dengan Transistor

Regulator This is basically the zener regulator is configured with an NPN transistor to produce a large amount of cash. V BE is the base-voltage emitor of the size of the transistor Q1 between 0.2 - 0.7 volt depending on the type of transistor used. By ignoring the current IB flowing in the transistor base, can be counted prisoners of R2 that is needed is:

Circuit of regulator using diode Zener
Rangkaian regulator Diode Zener
Skema rangkaian Regulator menggunakan Diode Zener

Iz is a minimum flow required by dioda to reach the zener voltage is zener breakdown. Large currents can be known from the datasheet that the size of the approximately 20 mA

If the required portion of greater flow, calculation of base flow in the IB on the circuit can not be ignored anymore. As is known, large currents IC akan proportionate flow straight to the IB or with the right formula

Rangkaian regulator Diode ZenerFor such purpose, the transistor Q1 can be replaced with a Darlington tansistor usually have a value of b is quite large. With the Darlington transistor, the base flow of small currents can produce a larger IC

READMORE...
 
Skema Rangkaian Elektronika